ASTM D638-14 Poisson's Ratio for Plastics

Plastics tensile standards, such as ASTM D638, cover a range calculations including Poisson's Ratio - a calculation that has proven to be challenging to obtain repeatable and accurate results.

Poisson’s Ratio is measured anywhere in the linear region as long as the linear region extends past 0.25% strain. When the linear region does not extend to this strain value, the calculation is taken between 0.25% to 0.5% strain.

The challenges of testing to this standard are:

  • Repeatable strain measurement
  • Reducing knife edge effects
  • Minimizing operator influence
  • Reporting calculations in compliance with the standard
Poisson Ration Graph

Instron's Solution:

  • Repeatable strain measurement – An extensometer capable of measuring both axial and transverse strain with an accuracy of 1% is required by the standard.  Many labs may be using extensometers which are not in compliance with these requirements.  Poisson’s Ratio is measured in the elastic portion of the test where very little strain has occurred, it is important to consider this when selecting an appropriate extensometer.  Instron’s biaxial clip-on extensometers, such as 2650-563, provide the accuracy needed to obtain Poisson’s ratio.
  • Reducing knife edge effects – During testing, knife edge penetration or knife edge slipping can cause inaccurate results.  The 2650 series biaxial extensometers provide interchangeable knife edges to ensure that the extensometer is suitable for both rigid and softer plastics.  Options include conical point for extremely rigid materials, line contact for thermoplastics, and vee profiles for thin section test pieces.
  • Minimizing operator influence - Because the measurement of Poisson's Ratio is so sensitive, operators can influence results through factors such as specimen alignment and extensometer attachment.  Consistent specimen alignment can be achieved through the use of specimen centering devices.  Care should be taken when attaching the extensometer to ensure that it is centered on the specimen for each test.  
  • Reporting calculations in compliance with the standard – Instron Bluehill® Universal testing software has advanced pre-built methods available with pre-configured plastic specific calculations helping to ensure compliance.  Using features such as an appropriate preload is critical for achieving accurate, repeatable result. A preload eliminates the compressive forces on a specimen that often occur when initially placed into grips.

It is important to review ASTM D638-14 (A3) in order to fully understand the test setup, procedure, and results requirements.

To learn more visit: ASTM D638: THE DEFINITIVE GUIDE TO PLASTIC TENSILE TESTING

Related Content

Plastics Testing Solutions Brochure

The Plastics Testing Solutions brochure is a 40-page, applications-focused, and standards-based brochure. Important standards such as ISO 527-1, -2, -3, ISO 11443, ISO 75, ASTM D638, Astm D3835, are covered in a detailed testing challenge and solution format. The brochure addresses the most prominent and widely-used standards in the materials testing industry for plastics. Test types such as Impact, Rheology, Thermo-Mechanical, Specimen Preparation, Mechanical Testing, Dynamic/fatigue, and Hardness are described in great detail.

  • Applications
  • 11/15/2017
  • 2.1 MB

AVE 2 Non-Contacting Video Extensometer

The second generation Advanced Video Extensometer (AVE 2) utilizes patented measurement technology in the fastest, most accurate non-contacting strain measurement device commercially available.

  • Products
  • 1/26/2018
  • 1.3 MB

Automatic Contacting Extensometer - Model AutoX 750

The AutoX 750 is a high-resolution, long-travel automatic contacting extensometer. It can be mounted onto any electromechanical 3300, 5500, or 5900 table top and floor model systems, as well as LX, DX, HDX, and KN static hydraulic testing systems. It is well suited for applications involving plastics, metals, biomedical, composites, elastomers, and more. The AutoX has a maximum travel of 750 mm and accuracy of ± 1 µm.

  • Products
  • 8/15/2013
  • 1.4 MB

5900 Series Premier Testing Systems Brochure

5900 Universal Testing Systems are engineered for precision, built for durability, and offer the flexibility for changing requirements. They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator. A wide range of models are available for testing capacities from < 100N up to 600kN.

  • Products
  • 1/22/2019
  • 6.8 MB

TestMaster AT3

The newest automated testing systems for plastics: the TestMaster AT3 for tensile testing and the TestMaster AT3+ for tensile and flex testing. These automated systems are designed to meet the testing requirements of ASTM D638 and D790, as well as ISO 527 and 178.

  • Press Releases
  • 9/23/2015
  • 108.1 KB

Automated Specimen Handling Systems

Available for tensile, flexural, and compression testing, Instron® TestMaster Automated Testing Solutions can improved the safety and productivity of testing for a wide range of materials and specimen sizes.

  • Products
  • 4/16/2018
  • 3.6 MB

Bluehill Universal Brochure

Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience. Discover simpler and smarter testing with features such as pre-loaded test methods, QuickTest in seconds, enhanced data exporting: and Instron Connect – a new feature that provides a direct communication link to Service. Users of previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest version of Bluehill.

  • Products
  • 2/26/2017
  • 2.6 MB